/*
 * This header file contains hardware-dependent definitions for C programs.

    Set up for Big Board II by Michael Mee		1983-7-30
    Revision 0.0

	Includes initialization for use with modem, with thanks to
Gordon Banks.
 */

/*
 * Some console (video) terminal characteristics:
 */

#define TWIDTH	80	/* # of columns	*/
#define TLENGTH	24	/* # of lines	*/
#define CLEARS	"\032"	/* String to clear screen on console	*/
#define INTOREV	"\033G4" /* String to switch console into reverse video	*/
#define OUTAREV "\033G0" /* String to switch console OUT of reverse video  */
#define ESC	'\033'	/* Standard ASCII 'escape' character	*/


/*
	The following definitions provide a portable low-level interface
	for direct I/O to the  console and modem devices. The values
	used here are only for example; be certain to go in and customize
	them for your system! Note that only one of the two sections
	(I/O port vs. memory mapped) will be needed for your system,
	so feel free to edit the unused section out of the file and remove
	the conditional compilation lines around the section you end up
	using.
*/
						/* Console */
#define CON_TBE		(TRUE)		/* Memory mapped screen always rdy */
#define CON_RDA		(bios(2,0))
#define CON_TDATA(byte)	(bios(4,byte))
#define CON_RDATA	(bios(3,0))

						/* Modem */
/*************
	Comment out the appropriate block for SIO A/B
							*************/
#define SIOA	/* change to SIOB for B port */

#ifdef SIOA
#define CPORT 	0x81			/* sio A control port */
#define DPORT 	0x80			/*  '      data   '   */
#define BAUDPORT 0x89			/* CTC B channel 1    */
#endif
#ifdef SIOB
#define CPORT	0x83			/* sio B control port */
#define DPORT	0x82			/*  '      data   '   */
#define BAUDPORT 0x88			/* CTC B channel 0    */
#endif

#define	MOD_TBE		(inp(CPORT) & 4)
#define MOD_RDA		(inp(CPORT) & 1)
#define	MOD_TDATA(byte)	(outp(DPORT, byte))
#define	MOD_RDATA	(inp(DPORT))


/**********  init - set up SIO (port A)
	For 8 bits, no parity, 1 start & stop bit

Add a call to init() from TELED, or incorporate this into
your BIOS to set up your SIO & CTC for modem use.

( I haven't checked this for port B.  Check SIO documentation
 if you have problems - and channel A WILL work)
						  *********/

#define X8BIT	0x60	/* transmit 8 bits */
#define XDTR	0x80	/* ready to transmit */
#define XBREAK	0x10	/* transmit a break */
#define XENABLE 0x08	/* transmit enable */
#define XRTS	0x02	/* Ready to send */
#define R8BIT	0xC0	/* receive 8 bits */
#define R1STOP  0x04	/* receive 1 stop bit */
#define RENABLE 1	/* receive enable */
#define R16CLCK 0x40	/* 16 x clock mode */
#define BAUDPORT 0	/* baud rate generator port (SIO chan A) */


init()		/* set up modem port */
{
	outp(BAUDPORT, 0x47);		/* set up baud rate */
	outp(BAUDPORT, 128);		/* (to 300) */
	outp(CPORT, 4);			/* select SIO reg 4 */
	outp(CPORT, R16CLCK | 0x04); 	/* 16 clock, 1 stop bit */
	outp(CPORT, 3);			/* reg 3 */
	outp(CPORT, R8BIT | RENABLE);	/* 8 bits, read enable */
	outp(CPORT, 5);			/* reg 5 */
	outp(CPORT, XDTR | X8BIT | XENABLE | XRTS);
}